加拿大华人论坛 加拿大生活信息有人家用sasktel的光纤连自己家的无线路由器吗？有事请教。。。

在加拿大

如题

评论
What's up? (sorry but I can only type in English on my computer)

评论
greentree8 说:What's up? (sorry but I can only type in English on my computer)点击展开...故事是这样的：自己买了无线路由器，在家里架VPN服务器给国内的朋友用。原来用access的，他们给换了个盒子，就是个纯cable modem，这样我的路由器的wan口就直接从access拿到个动态的公网IP， 配合路由器上的ddns设置，从外面可以直接访问vpn，及路由器的配置啥的。现在用sasktel的光纤，希望能做到同样的事情，BUT：我的路由器wan口接sasktel的actiontec v1000h的lan1，它的wan口接ONT，即使他们把v1000h配置成了bridge mode，我的路由器的wan口拿到的也只是172的内网地址，公网地址还是在v1000h的wan口上。家里相当于两个路由器级联了。（周五电话他们说，动态IP下做不了bridge，要bridge就要申请静态IP，whichmeans要extra$。臭LM！！！）我就在尝试把我的router的wan口直接接ONT的口，但对于v1000h不太了解，不知它的wan口和一般的路由器的wan口是不是一样。我直接接上但是显示拿不到任何IP地址。所以问题是：1：到底能不能这么接；2：如果从技术上可行，又有哪些关键配置？？多谢了。

评论
Actiontec v1000h is also called gateway. In a more general term, it is modem as on the copper xDSL high speed lines.And the ONT is more like a signal converter that converts the optic fibre signal to the electric signal that goes to Actiontec.In terms of your first question, it is not doable: connecting your router to ONT directly will not give you the public IP address you want.However, if you connect your own router to the LAN port on Actiontec, and then configure Actiontec properly, your router should be able to use the modem (Actiontec) WAN IP address as its own. The modem (Actiontec) WAN IP address is a public IP that can be found from the Actiontec GUI, for example, 142....Please follow the steps below to configure the Actiontec gateway from any of your computers that is connected directly to the Actiontec network either through wi-fi or ethernet:1. Make sure your router is connected to an Actionac gateway LAN port;2. From your computer, go to 172.16.1.254 which will give you Actiontec GUI;3. From the top right hand, there is a Password field that is supposed to be the default 10 character system password located at the bottom of the Actiontec gateway box. If you have never changed this login password, that default system password should let you login to Actiontec interface.4. After you login, you will see a list of all the devices that are currently connected the Actiontec. One of those devices should be your router and router should be with a private IP like 172...5. Next, click on Firewall.6. From the left side, click on DMZ Hosting.7. Go through the 3 steps under DMZ Hosting: Enable - Select a device (your router) - ApplyYour router should now be accessible by the Actiontec WAN IP Address (public IP) located at the top left side of the home page of the Actiontec GUI.(This bypasses the firewall on Actiontec and exposes your router directly to the external network. Actiontec WAN IP address may change once Actiontec gets rebooted -- static IP won't change. So you need to know what you are doing.)Hope the above will get you started toward the right direction.

评论
greentree8 说:Actiontec v1000h is also called gateway. In a more general term, it is modem as on the copper xDSL high speed lines.And the ONT is more like a signal converter that converts the optic fibre signal to the electric signal that goes to Actiontec.In terms of your first question, it is not doable: connecting your router to ONT directly will not give you the public IP address you want.However, if you connect your own router to the LAN port on Actiontec, and then configure Actiontec properly, your router should be able to use the modem (Actiontec) WAN IP address as its own. The modem (Actiontec) WAN IP address is a public IP that can be found from the Actiontec GUI, for example, 142....Please follow the steps below to configure the Actiontec gateway from any of your computers that is connected directly to the Actiontec network either through wi-fi or ethernet:1. Make sure your router is connected to an Actionac gateway LAN port;2. From your computer, go to 172.16.1.254 which will give you Actiontec GUI;3. From the top right hand, there is a Password field that is supposed to be the default 10 character system password located at the bottom of the Actiontec gateway box. If you have never changed this login password, that default system password should let you login to Actiontec interface.4. After you login, you will see a list of all the devices that are currently connected the Actiontec. One of those devices should be your router and router should be with a private IP like 172...5. Next, click on Firewall.6. From the left side, click on DMZ Hosting.7. Go through the 3 steps under DMZ Hosting: Enable - Select a device (your router) - ApplyYour router should now be accessible by the Actiontec WAN IP Address (public IP) located at the top left side of the home page of the Actiontec GUI.(This bypasses the firewall on Actiontec and exposes your router directly to the external network. Actiontec WAN IP address may change once Actiontec gets rebooted -- static IP won't change. So you need to know what you are doing.)Hope the above will get you started toward the right direction.点击展开...万分感谢您的回复。我现在就是这么做的。但从我的路由器上看，wan口依然是172的地址。看了您的回复，我又试了一下，居然可以从外面访问路由器了。（记得前几天试还不行，不知道原因了）。我之前一直纠结路由器wan口是不是公网地址了。现在唯一的‘问题‘是，DDNS的配置要在v1000h上做了，不能在我的路由器上做。但v1000h也可以做。再次感谢。。。

评论
greentree8 说:Actiontec v1000h is also called gateway. In a more general term, it is modem as on the copper xDSL high speed lines.And the ONT is more like a signal converter that converts the optic fibre signal to the electric signal that goes to Actiontec.In terms of your first question, it is not doable: connecting your router to ONT directly will not give you the public IP address you want.However, if you connect your own router to the LAN port on Actiontec, and then configure Actiontec properly, your router should be able to use the modem (Actiontec) WAN IP address as its own. The modem (Actiontec) WAN IP address is a public IP that can be found from the Actiontec GUI, for example, 142....Please follow the steps below to configure the Actiontec gateway from any of your computers that is connected directly to the Actiontec network either through wi-fi or ethernet:1. Make sure your router is connected to an Actionac gateway LAN port;2. From your computer, go to 172.16.1.254 which will give you Actiontec GUI;3. From the top right hand, there is a Password field that is supposed to be the default 10 character system password located at the bottom of the Actiontec gateway box. If you have never changed this login password, that default system password should let you login to Actiontec interface.4. After you login, you will see a list of all the devices that are currently connected the Actiontec. One of those devices should be your router and router should be with a private IP like 172...5. Next, click on Firewall.6. From the left side, click on DMZ Hosting.7. Go through the 3 steps under DMZ Hosting: Enable - Select a device (your router) - ApplyYour router should now be accessible by the Actiontec WAN IP Address (public IP) located at the top left side of the home page of the Actiontec GUI.(This bypasses the firewall on Actiontec and exposes your router directly to the external network. Actiontec WAN IP address may change once Actiontec gets rebooted -- static IP won't change. So you need to know what you are doing.)Hope the above will get you started toward the right direction.点击展开...又发现了一个问题，之前看别人连telus/bell的经验，说要把自己路由器的wan mac改成和v1000h的一样，我也找着做了。刚才手欠把那个删了，结果现在从外面连不上了。看来还是需要的。

评论
DDNS的配置在v1000h上做，vpn 在路由器上做就可以了。我是这样搞的，效果还可以。

评论
walleye 说:DDNS的配置在v1000h上做，vpn 在路由器上做就可以了。我是这样搞的，效果还可以。点击展开...是的，我现在也这么做了。基本的要求全实现了。下一步是照搬这个配置到国内家里，反向翻墙，便于看视频啥的。

评论
walleye 说:DDNS的配置在v1000h上做，vpn 在路由器上做就可以了。我是这样搞的，效果还可以。点击展开...咋配置DDNS呢？有免费的么？

评论
Kyleli 说:咋配置DDNS呢？有免费的么？点击展开...很多呀，自己狗一下。我用的是noip，免费的就只能用2级域名，并且一定时间就要上他们的网上点一下，以示要继续使用。

 ·加拿大留学移民 双持用红本申请美签B1
 ·生活百科 钉子/框架枪的区别？
·生活百科 多米诺骨牌交付